What do we need to pay attention to when packing the belt?
1. Before turning on the power, make sure to turn off the motor and electric power switch.
2. Check if the circulating cooling water is open. When the strapping machine starts and heats up, it must ensure that the circulators of the circulating cooling water for the hydraulic oil and the cartridge are open and open.
3, when the strap machine starts, first use the jog start (ie press the motor start button, the motor starts, then disconnect, after 1-2 seconds, then repeat the jog to start and disconnect 3 to 4 times. When the oil pump When the motor rotates, listen for unusual noises. If there is abnormal noise, stop the operation immediately.
4. Check the parameters of the machine during the operation and operation. First, place the machine in the manual state, press the relevant button, and visually check the pressure gauge to predict the pressure of each section. When the screw is not heated to the set value (normal operation Temperature) Remember not to turn on the machine. Failure to do so may result in failure or damage to the strapping screw.
5. Check and adjust the function parameters of the strapping machine. It is necessary to first turn off the power of the motor and the oil pump. If unavoidable, special care should be taken when it is forbidden to operate the keys on the control panel of the machine while the other hand is doing any work within the lock mold area or touching any moving parts on the packing machine. It is absolutely forbidden for two persons to operate. A strapping machine: (ie, a person who operates the buttons on the strapping machine control panel while the other person is operating or in contact with the movement within the clamping zone)
6. Check the safety operation of the machine: Place the strapping machine in the manual state, press the open button, and let the strapping machine completely open the mold to the end position. At this time, observe whether the open end position of the machine is in the set position, if the open mode exceeds When the end position is set, the machine has a problem and the machine cannot work; when the strapping machine is in the manual mode, press the mode-lock button to fully clamp the strapping machine (to the end position of the clamping mode) and then press the front of the machine. In the middle of the red rapid rise switch, strapping machine that is made to open the mold action, open the mold to the end of the set position; or the strapping machine in a semi-automatic state, start the motor, both hands at the same time press the machine before the two mold button (left and right Each side, green) strapping machine fast clamping, when the mold is closed to slow mode, release the hands, quickly press the middle of the platform before the middle position button (red, rapid rise) closing the mold should be immediately terminated, In addition, the strapping machine quickly makes a mold opening action, so that the closing mold is completely opened to the end position. If the pressing is completed, the mold clamping is not terminated immediately and the mold clamping is continued. At this time, the motor should be immediately turned off and the strapping machine must be turned off. stop Work to repair; strapping machine equipped with a clamping sensor device, so that the strapping machine power, start the motor, respectively, press the electric heat, mold adjustment, mold opening key, so that the mold to set the termination position, and then hold in one hand The object is carefully placed in the mold sensing area, the sensor light will shine, and the other hand will press the mold-lock switch. At this time, the mold-locking will not move and the mold will not be closed, or the mold-packing machine will be pressed slowly with one hand. Lower the mold, at this time the other hand holding the object carefully into the induction area of ​​the mold, this time the mold should be immediately terminated, and the strapping machine can quickly make the mold opening operation, so that the mold being closed can be completely opened. Terminate the position to normal use, otherwise stop repair.
7. Before inspecting the strapping machine or doing any work on the strapping machine, be sure to remember the safety operation before touching any moving parts or pressure electrical parts. It is necessary to cut off the power of the pump motor before it can guarantee safety.
8. When the machine stops working or when there is a sudden power failure, the power switch should be turned off for safety and protection of electrical equipment.
Remember that failure to perform the above procedures may result in serious hazards and strapping problems.
In the purchase of packing belts, China's packing belt trading network as a professional platform is your best choice. The platform has brought in thousands of packing belt manufacturers from across the country. It has a strict check on the quality of people's wages and effectively guarantees buyers' rights and interests. Because it's professional, it's trustworthy. The massive packaging belts supply and purchase information are waiting for you! If you want to pay attention to more packaging information, please come here!
The above information comes from China's packing belt trading network:
Polyester Polar Fleece Blanket
Fleece Blanket,Polar Fleece Blanket,Printed Polar Fleece Blanket,Bright Color Polar Fleece Blanket
SHAOXING WUYUN TEXTILE CO.,LTD , https://www.kexintextile.com